top of page
STRUCTURAL CLADDING ADHESIVE
FOR PERMAFORM PVC PERMANENT FORMWORK
RitterBuild™ Adhesive has been tested for use on Permaform PVC Permanent Formwork Systems featured on this webpage.
MANUFACTURED IN GERMANY UNDER LICENSE
NO MIXING, NO MESS, NO WASTE
-
EXCELLENT BONDING TO PVC SUBSTRATES
-
EXCELLENT BONDING TO STONE PRODUCTS
-
HIGH JOINT MOVEMENT CAPABILITIES
-
HIGH SHEAR STRENGTH
-
TENSILE STRENGTH - 3MPA
-
REDUCE WALL FIXING REQUIREMENTS
-
SINGLE COMPONENT - NO MIXING REQUIRED
-
FASTER INSTALLATION
-
SUITABLE FOR DAMP MASONRY SURFACES
-
ELONGATION - 240%
SUPERIOR PERFORMANCE
RitterBuild™ High Bond Adhesive is a single-component polymer formulated for bonding and sealing cladding products onto Permaform PVC Permanent Formwork. It consists of a modified polymer technology that delivers an optimum balance of adhesion, cohesive strength and vibration absorption. It allows dynamic stresses to be compensated and conventional fasteners to be partially or completely replaced.
SUPERIOR ADHESION
High resistance to peel forces.
Adhesive to PVC - 36kg p/sqcm
ELONGATION RECOVERY
High elongation recovery under sheer or tensile stress.
SUBSTRATE EXPANSON
Accommodates high variation in substrate expansion.
CUT & GLUE IMMEDIATELY
NO NEED TO DRY BEFORE APPLYING
RitterBuild™ Bond & Seal will significantly increase productivity by enabling you to apply stone and other masonry cladding products immediately after 'wet cutting'. This enables applicators to focus on a single area of the installation, improving workflow, continuity and quality of the end result.
INSTALL IN WET WEATHER
MAINTAIN PROJECT DEADLINES & IMPROVE PRODUCTIVITY
Eliminate the need to stop and start projects. The RitterBond™ Bond & Seal Adhesive curing process is promoted by moisture/water. The adhesive can be applied onto damp surfaces without compromising its performance providing applicators more flexibility when scheduling outdoor work.
EXTREME CLIMATE TOLERANCE
BROAD IN-SERVICE TEMPERATURE RANGE
Cyclic thermal changes can affect building structures causing cracking and bonding failures. RitterBond™ not only accommodates for these changes with its high elongation and adhesion characteristics, it also maintains these properties within a broad range of operating temperatures of -40°C to +100°C.
BONDS TO MANY MATERIALS TYPES
HIGH STRUCTURAL BONDING FOR A BROAD RANGE OF CONSTRUCTION APPLICATIONS.
Whether you require a high bonding solution for stone to PVC, PVC to glass, stone to aluminium or steel RitterBuild HighBond and Seal can offer a reliable bonding solution for many applications and material types.
SIMPLE 2 STEP APPLICATION
PRIME
BONDING AGENT
Spray RitterBuild™ Bonding Agent onto all PVC Formwork surface
BOND
Adhesive
Apply the RitterBond™ Adhesive to the cladding component and place into position.
QUICK & EASY
SUPERIOR ADHESION
EXTREME STRENGTH
INCORPORATING
UV TRACING
TECHNOLOGY
The Ritterbuild™ Bond & Seal Adhesive incorporates UV Tracing Technology to ensure adequate coverage of the Primer is achieved during installation. It can also be used as a tool to validate application compliance to avoid inferior product substitution.
KEY DATA:
Description
Data
Elongation to Break
>25 N/mm2
Cure Rate, mm/24 hrs
5%
Density, g/cm3
>250N
Tensile Strength Mpa
>450N
Shore-A-Hardness
5 N/mm2
Application Temperature, °C
6 N/mm2
Operating Temperature range, °C
4 N/mm2
Sag Resistance:
2 N/mm2
Maximum Load (kN) - PVC Surfaces coated with RitterBuild™ Bonding Agent 303
1.4 kN
Shear Strength (Mpa) - PVC Surfaces coated with RitterBuild™ Bonding Agent 303
2.3 MPA
Data Sheet Downloads
Technical Data Sheets
Safety Data Sheets
bottom of page